Hi Mats,
Denis Welch Motorsports can sell you a new main shaft, see link below.
https://www.bighealey.co.uk/jaguar/jaguar-gearbox
Search found 128 matches
- Fri Aug 24, 2018 3:32 am
- Forum: Technical
- Topic: Main shaft issue
- Replies: 6
- Views: 3297
Re: New Boy
I remember that program but I didn't know that they were married.
- Wed Sep 27, 2017 12:27 pm
- Forum: Technical
- Topic: tappet clearance advise
- Replies: 59
- Views: 18598
Re: tappet clearance advise
Hugo, the original cams have straight sides the parabolic cams are not straight leading to the valves starting to open sooner and close later (Increased duration). This means that maintaining the same gap as the original cams leads to an increase in duration. Increasing the gap has the effect of red...
- Sat Jul 08, 2017 4:45 am
- Forum: General
- Topic: STOLEN - S1 Silver/Blue FHC from Essex
- Replies: 26
- Views: 10767
Re: STOLEN - S1 Silver/Blue FHC from Essex
Peter, I would say it's hand held footage of the security camera monitor during playback. Maybe the owner doesn't know how to retrieve the original file from the security camera hard drive for posting on this forum.
- Wed Jan 25, 2017 7:34 am
- Forum: Series 1
- Topic: FACTORY FIT - Series 1 4.2
- Replies: 65
- Views: 208848
Re: FACTORY FIT - Series 1 4.2
Nice pictures David, did you notice the cotton covered edge trim on the B posts?
- Wed Dec 07, 2016 4:58 am
- Forum: General
- Topic: British Princess Nina Aga Khan E type
- Replies: 21
- Views: 9315
Re: British Princess Nina Aga Khan E type
1962 3.8? If you take a look at the pictures of the body shell it has a later 4.2 panel for mounting for the Lockheed brake servo and no cooling fan motor mounting on the picture frame as per S2.
- Fri Sep 23, 2016 6:21 pm
- Forum: Technical
- Topic: Crown Wheel & Pinion 3.07
- Replies: 7
- Views: 4569
Re: Crown Wheel & Pinion 3.07
3586 stamped on the crown wheel and etched on the pinion probably means they are a matched set. The cone setting distance should also be etched on the pinion ground face and is nominally 0 but usually deviates either side of zero such as + 3 or -3 for example. the other stamped numbers you refer to ...
- Fri Sep 23, 2016 6:13 am
- Forum: Technical
- Topic: Crown Wheel & Pinion 3.07
- Replies: 7
- Views: 4569
Re: Crown Wheel & Pinion 3.07
The pinion should be stamped on its ground face with pinion offset and cone setting distance for that particular crown wheel and pinion assuming it's a matched set. The crown wheel in addition to the stamped information shown in your picture, should have the relevant backlash hand written with an et...
- Sun Sep 18, 2016 1:13 pm
- Forum: Technical
- Topic: Propshaft bolts/nuts size?
- Replies: 9
- Views: 3914
Re: Propshaft bolts/nuts size?
Propshaft bolts should be UNF not UNC.
- Sun Sep 18, 2016 1:07 pm
- Forum: Technical
- Topic: Redrilled and strengthened picture frame
- Replies: 1
- Views: 2206
Re: Redrilled and strengthened picture frame
Etype Fabs, available from Hutsons.
- Mon Sep 12, 2016 4:45 pm
- Forum: Technical
- Topic: Propshaft bolts/nuts size?
- Replies: 9
- Views: 3914
Re: Propshaft bolts/nuts size?
3/8" sounds right, they are certainly not 9/16" What did you measure the head size?
- Fri Jul 15, 2016 1:04 pm
- Forum: Technical
- Topic: Clutch prob?
- Replies: 19
- Views: 6328
Re: Clutch prob?
Looks like the release bearing is worn out also the input shaft splines should have a light coating of grease. In your picture they are dry and rusty.
- Sat Jul 09, 2016 1:22 pm
- Forum: Series 1
- Topic: Inner sill dimension
- Replies: 3
- Views: 2564
Re: Inner sill dimension
8 inches from the bulkhead face (Not the edge of the flanges as indicated in your picture) to the front face of the inner sill.
- Wed Jun 01, 2016 12:16 pm
- Forum: Series 1
- Topic: Underfelt fitment
- Replies: 2
- Views: 2556
- Wed May 25, 2016 3:07 am
- Forum: Series 1
- Topic: Wiper rack adjuster
- Replies: 3
- Views: 2274
- Thu Mar 31, 2016 6:46 am
- Forum: Technical
- Topic: What type of paint ??
- Replies: 4
- Views: 3236
If it's a wrinkle finish you can use this paint from Frost Automotive and if the part is aluminium use an etch primer first. To get the finished coat to wrinkle in an even fashion take the freshly painted piece into a very warm room otherwise you will end up with smooth areas (no wrinkle) http://www...
- Sun Mar 13, 2016 5:16 am
- Forum: Series 1
- Topic: Door hinge to A pillar bolt finishes
- Replies: 1
- Views: 2059
- Fri Feb 19, 2016 8:00 am
- Forum: General
- Topic: Evolution E-types
- Replies: 28
- Views: 12900
- Thu Feb 11, 2016 2:37 pm
- Forum: Technical
- Topic: cylinder head bolt chrome washers
- Replies: 6
- Views: 2924