Search found 38 matches
- Sat Feb 26, 2022 4:32 pm
- Forum: Series 3
- Topic: Relay position.
- Replies: 6
- Views: 2220
Re: Relay position.
Ignition relay is on the RH firewall next to the windscreen motor on my RHD car
- Sat Jan 29, 2022 5:31 pm
- Forum: Series 3
- Topic: Relay position.
- Replies: 6
- Views: 2220
Re: Relay position.
One near the battery is the horn relay, I don’t have the relay near the transmission tunnel but I think if you have aircon on your car it is for that.
- Mon Jan 17, 2022 8:28 pm
- Forum: Series 3
- Topic: Fuel Filter
- Replies: 6
- Views: 1803
Re: Fuel Filter
There was the metal fuel filter housing that came later for the series 3 did they send the wrong one in error?
- Mon Jan 11, 2021 7:17 pm
- Forum: Series 3
- Topic: V12 Engine Instruction Manual
- Replies: 22
- Views: 6307
Re: V12 Engine Instruction Manual
Hi the emissions set up depends on the model and year for where the connections go to the thermacs. On my 1973 car the RH unit goes to RH servo further along the air trumpet and the other to a T off the thermionic valve and the LH unit goes to the rear induction manifold and the LH servo valve In th...
- Sun Jan 10, 2021 4:09 pm
- Forum: Series 3
- Topic: V12 Engine Instruction Manual
- Replies: 22
- Views: 6307
Re: V12 Engine Instruction Manual
Hello is this what you need? JAGUAR V12 ENGINE - ITS DESIGN AND BACKGROUND. By Walter T. F. Hassan. Booklet produced by the Technical Administrative and Supervisory Section of the Amalgamated Union of Engineering Workers. Paperback booklet. 52 pages. Illustrated with black and white drawings and pho...
- Thu Nov 19, 2020 4:05 pm
- Forum: Series 3
- Topic: Manifold heat shield springs
- Replies: 4
- Views: 1715
Re: Manifold heat shield springs
Thanks Marek, so it is literally the spring that holds it. I have the induction manifolds and mud shields off currently so will see how easy it is to fit in situ.
Nige.
Nige.
- Thu Nov 19, 2020 2:42 pm
- Forum: Series 3
- Topic: Manifold heat shield springs
- Replies: 4
- Views: 1715
Re: Manifold heat shield springs
What attaches the bracket or is it the spring that holds the bracket?
Nigel
Nigel
- Sun Aug 02, 2020 7:45 pm
- Forum: Series 3
- Topic: Courtesy light Wire routing S3 (RHD) OTS
- Replies: 2
- Views: 1074
Re: Courtesy light Wire routing S3 (RHD) OTS
Hi Marek Yes I have the dash tops off the purple and white wire is coming from the loom which looks like it is from the switches with most terminating to join the loom down the RHS of the car (aerial sense, indicators etc) but cant see a purple and white wire in the bundle from the courtesy light. I...
- Fri Jul 31, 2020 9:10 pm
- Forum: Series 3
- Topic: Courtesy light Wire routing S3 (RHD) OTS
- Replies: 2
- Views: 1074
Courtesy light Wire routing S3 (RHD) OTS
I have a purple and white wire coming out behind the steering wheel/ speedo/rev counter area of the dash loom, I presume this must connect to the driver's side courtesy light but where would the routing of this be as I can't see a corresponding wire to connect to? It has a standard bullet connector....
- Tue Jun 02, 2020 8:19 pm
- Forum: Series 3
- Topic: S3 underdash hardura and mill board RHD RH side
- Replies: 2
- Views: 1456
Re: S3 underdash hardura and mill board RHD RH side
Thanks Nigel appreciate that
- Mon Jun 01, 2020 8:07 am
- Forum: Series 3
- Topic: S3 underdash hardura and mill board RHD RH side
- Replies: 2
- Views: 1456
S3 underdash hardura and mill board RHD RH side
Ok so enjoying time with the Jag during lock down doing some trim work putting right the previous owners work. On the rh side does the under dash hardura bend over the front lip to go under where the steering column Bracket lower bolts fit and do they also glue onto the steering shaft cover? Photos ...
- Fri Aug 31, 2018 6:28 pm
- Forum: Series 3
- Topic: Routing of reverse light wires
- Replies: 4
- Views: 2270
Re: Routing of reverse light wires
Found the holes on both sides for anyone else looking with the rear lights out of the car in the inner void it is on the top face closest to bumper almost as far in as you can reach. Then use a piece of wire to feed through and drag the number plate wires and reverse lamp wire.
Regards
Nigel
Regards
Nigel
- Tue Jun 05, 2018 8:40 pm
- Forum: Series 3
- Topic: Routing of reverse light wires
- Replies: 4
- Views: 2270
Re: Routing of reverse light wires
Thanks Ole
I already have the rear lh tail light out but unlike the rh side can not find a route into the void the number plate lamp and reverse lamp wiring goes into so wondered if they initially ran under the little ledge in the boot/trunk beside the petrol tank.
Nigel
I already have the rear lh tail light out but unlike the rh side can not find a route into the void the number plate lamp and reverse lamp wiring goes into so wondered if they initially ran under the little ledge in the boot/trunk beside the petrol tank.
Nigel
- Mon Jun 04, 2018 10:47 pm
- Forum: Series 3
- Topic: Routing of reverse light wires
- Replies: 4
- Views: 2270
Routing of reverse light wires
Dear All, Correcting some mistakes made to the wiring of my S3 and wanted to know how to run the number plate and reverse light wiring. I presume they both run from the LH side loom but can not feel a gap to run them into the void behind the trunk from the rear light, do they run under the lip of th...
- Tue Jan 24, 2017 6:55 pm
- Forum: Series 3
- Topic: Changing paint colour
- Replies: 9
- Views: 4426
Re: Changing paint colour
Welcome
Kept mine lavender blue admittedly with dark blue interior. Love the 70s colours on the S3 roadster
Nigel
Kept mine lavender blue admittedly with dark blue interior. Love the 70s colours on the S3 roadster
Nigel
- Tue Nov 22, 2016 8:10 pm
- Forum: Series 3
- Topic: Stonechip paint
- Replies: 5
- Views: 2865
Re: Stonechip paint
Thanks chaps. What about the boot area I guess just the floor and not the contoured upturns which lead on the rear wings ?
Regards
Nigel
Regards
Nigel
- Tue Nov 22, 2016 7:17 am
- Forum: Series 3
- Topic: Stonechip paint
- Replies: 5
- Views: 2865
Stonechip paint
Coming time to respray my series 3 but the question is how far up the sills do I take the stone chip paint and what profile does it follow on the boot pan. Clear on wheel arches.
Thanks Nigel
Thanks Nigel
- Tue Apr 05, 2016 8:12 pm
- Forum: Series 3
- Topic: Insulating panels on petrol tank
- Replies: 9
- Views: 4632
- Sat Apr 02, 2016 10:48 pm
- Forum: Series 3
- Topic: Insulating panels on petrol tank
- Replies: 9
- Views: 4632
Insulating panels on petrol tank
Can't find any part numbers but what are people using for the insulating panel facing the spare wheel and the pillar by the fuel filter?
Cheers Nigel
Cheers Nigel
- Sat Mar 26, 2016 5:58 pm
- Forum: Series 3
- Topic: Hood stowage cover fixtures
- Replies: 3
- Views: 2525