Search found 276 matches

by MLBS3V12
Fri May 01, 2020 12:39 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

Still a few bits to be reassembled


Image
by MLBS3V12
Fri May 01, 2020 11:34 am
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

Hi, I've changed the plugs and set the pot @0.36V. Not easy for sure. It looks like it has less fumes. But the problem is that the car is not far enough reassembled to go on the road and run enough @higher rpm. :hammerdrill: I 'll set this topic aside for now. I'll come back later on and after been ...
by MLBS3V12
Thu Apr 30, 2020 1:42 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

Hi, Ive measured the pot as you did. Between G and Y I find 4,47K, Y and R starts at 0,65K until 3k. Not the same result. As I understand that the Red is the signal, Mine is high compare to yours. In other words at idle I've already a signal from higher rev. I'll reduce the value by setting up anoth...
by MLBS3V12
Wed Apr 29, 2020 6:55 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

I ll look at the pot tomorow morning.
:thankyouyellow:
by MLBS3V12
Wed Apr 29, 2020 6:03 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

On the doc from R Bywater to get an XJS engine used in the E type he indicates that this switch brings 15% more @ full throttle. If mine gives not a clear 0 , it may bring these 15% more, dont you think so ?
by MLBS3V12
Wed Apr 29, 2020 5:42 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

I' m talking about this "valve", Depending of the Jaguar litterature, it is call switch or valve: https://i.postimg.cc/Kv41K3Sr/Capture-vaccum-valve.jpg because engine off the resistance is not 0 but ~20 Ohm. And it opens with a vaccum. If the engine needs 0 ohm, my probleme could be there, dont you...
by MLBS3V12
Wed Apr 29, 2020 5:07 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

I though to have some test to do and finally find something.... For now on, I'm stuck with the same result. Philip, you were right, plugs dead very quickly when there is too much fuel. I've replaced the vaccum pipe, same result.... I had a set of injectors plugged on another rail. I've tried it, sam...
by MLBS3V12
Mon Apr 27, 2020 12:30 pm
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

Hi Philip Thank you for your kind reaction. About your remarks, 1) I confirm that the small hose is connected on both side. However I’m wondering if I’ve not bent it during the re routing from the wiring. I’ll check this. 2) I’ll verify the one dedicated to the EFI. I do have fit a new one at the re...
by MLBS3V12
Mon Apr 27, 2020 6:28 am
Forum: Series 3
Topic: V12 ECU
Replies: 70
Views: 11370
France

Re: V12 ECU

Yesterday was a first running test with my EFI E Type under restauration:

The brakes, the gear box on first and the reverse gear, the power steering, all seem to be good! :bouncyyellow:
I now have to solve the too far richness of the engine. :scratchheadyellow:
by MLBS3V12
Mon Apr 20, 2020 5:15 pm
Forum: Series 3
Topic: Series 3 Brake Servo Replacement⅚
Replies: 12
Views: 1630
France

Re: Series 3 Brake Servo Replacement⅚

Because you are going to change nearly all the brake fluid, Ask your guy to use silicon brake fluid. No more moisture in the circuit and no danger for your painting.
by MLBS3V12
Mon Apr 20, 2020 5:10 pm
Forum: Series 3
Topic: Help for the wiring loom
Replies: 22
Views: 3578
France

Re: Help for the wiring loom

Thank you Colin, your information will help soon as I' m close from connecting the brake items. these last days, I've reconnected all to make the following functions running well: -wippers motor ith the 2 speeds -washer engine -all thre rear lights exept the reverse ones. Because I do not changed th...
by MLBS3V12
Mon Apr 20, 2020 4:38 pm
Forum: Series 3
Topic: Help for the wiring loom
Replies: 22
Views: 3578
France

Re: Help for the wiring loom

Dear Michel, While you have all of that apart, cut yourself an access hole and make a cover plate at the bottom front right of the transmission tunnel cover, so you have good access to the clutch slave cylinder and can easily bleed the clutch without dismantling half of the car or having to crawl u...
by MLBS3V12
Mon Apr 20, 2020 4:36 pm
Forum: Series 3
Topic: Help for the wiring loom
Replies: 22
Views: 3578
France

Re: Help for the wiring loom

Hello Simon,

a last question ( at least for no ) on a green wire on your picture

Image

Image

I dont know what it is for.
by MLBS3V12
Sun Apr 05, 2020 12:50 pm
Forum: Technical
Topic: Original soundproofing material
Replies: 5
Views: 853
France

Re: Original soundproofing material

:thankyouyellow:
by MLBS3V12
Wed Apr 01, 2020 6:48 pm
Forum: Technical
Topic: Original soundproofing material
Replies: 5
Views: 853
France

Re: Original soundproofing material

Hi Holger

Can you let us know more about the product you ve used ?
Manufacturer / reference....
How many square meters ?
I still have this step to do.
Regards
by MLBS3V12
Tue Mar 24, 2020 12:33 pm
Forum: Series 3
Topic: Black smoke Series 3 2+2
Replies: 41
Views: 5706
France

Re: Black smoke Series 3 2+2

Yes Philip,
I'm referring to the crank case ventilation pipe. If I'm not wrong this pipe is connected to the left bank only.
But finally I dont know what can brought to this side additionnal oil consummed into the 6 left side cylinders and neither why :scratchheadyellow:
by MLBS3V12
Tue Mar 24, 2020 10:03 am
Forum: Series 3
Topic: Black smoke Series 3 2+2
Replies: 41
Views: 5706
France

Re: Black smoke Series 3 2+2

Cant it be an oil issue coming from the engine depress pipe ?
by MLBS3V12
Tue Mar 24, 2020 9:59 am
Forum: Technical
Topic: Original soundproofing material
Replies: 5
Views: 853
France

Original soundproofing material

I've placed some Cool it insulation material in the body from my S3. https://i.postimg.cc/8cQnY8Zw/20200318-185655.jpg To go ahead on the soundproofing, I would like to do is to get the same kind of product that the one used by Jaguar. I know there are kits such this one: ebay.co.uk/itm/202720396823...
by MLBS3V12
Wed Mar 11, 2020 1:32 pm
Forum: Series 3
Topic: V12 Getrag 265 bellhousing
Replies: 23
Views: 2510
France

Re: V12 Getrag 265 bellhousing

Suppliers in UK and Germany still work on the Getrag 265 if a rework is requested.
Since I work on my own V12, Ive bought and sold several ones to help le in my restauration.😁
Not to hard to fing close from 1000€.
by MLBS3V12
Mon Mar 09, 2020 5:23 pm
Forum: Series 3
Topic: V12 Getrag 265 bellhousing
Replies: 23
Views: 2510
France

Re: V12 Getrag 265 bellhousing

I do have a such bell housing on my V12 without any adapter plate:


Image

But I dont know if it is a jaguar one.