The 'E' Type Forum

Full up. And then what? Wait for the fuel to deteriorate, scared to refill with what will be E5 in fact as well as name? E5 will not make any difference to my car. Not did E10, the many times I've had to fill up with it, sometimes for thousands of miles at a time. You could try one of the many new f...

The cam oil feed pipes can become blocked or restricted. I'll rephrase that. The cam oil feed pipe on my car did become blocked. It was blocked, to be more precise, the inlet feed pipe became blocked by swarf created when an undersize big end split pin rattled loose and the bits were sucked through ...

Not sure if it was just my car or..... I changed my headlamps including the mounts. I found the OE mount was upside down. Result? The vertical adjuster was originally under the headlamp unit. I changed the mounts and the headlamp such that my headlamp's vertical adjuster is on top of the headlamp. I...

My car definitely does not have an oil pressure warning light or even something that functions as one. If this is as a result of a modification then I'm not aware of it. The ignition earning light only indicates whether the alternator is charging.

Marek, No oil warning light on mine. I think only on some early 3.8s and some early S3s.

This thread prompted me to do this. https://i.postimg.cc/d3YG0P6L/IMG-20230803-170727164-2.jpg I prised the cap off a sender to see the gubbins inside. This is a bi-metal switch sender. Having reset the contacts using the rotating black plastic adjuster so that the contacts were just apart at no pre...

"Are you planning any work on yours?"
Darryl. No I am not doing anything to the locks. I did have the driver's door lock fail to release some time last year. A good spray with WD40 freed it up.

Cleaned components and a delivery of parts from SNGB today meant I could crack on.... One part to replace was the broken window frame mount. The new bracket didn't quite line up. So I pulled the door cap off (it had been rivetted on - why? It is supposed to be a push fit!) and pulled the window fram...

Further inspection...... https://i.postimg.cc/8P0Gq8x1/IMG-20230802-153437252.jpg The glass channel is not as bad as I thought. It will be preserved, but a new seal will be fitted. Once out ... https://i.postimg.cc/pXD7JwxG/IMG-20230802-154605114.jpg ..the regulator did look rough. But a spell with ...

The inspection........ https://i.postimg.cc/wjx3hgHk/IMG-3940.jpg The glass came out easily, but the rubber seal has seen better days. Evident on the glass is overspray from when the car was tarted up in 2002/3. https://i.postimg.cc/TP6xrcrv/IMG-3941.jpg This looks awful, but it is a mixture of rust...

.....is not a welcome noise. Today it came from the driver's door window regulator. Consequence? The window glass remained in its frame and didn't drop into the door. At least it will be raining tomorrow so I can spend some time in the garage removing the door card to inspect the regulator and glass...

C'mon, show us the naughty bits.

I found two things wrong with mine. One was the generator the other was the needle pivot. The generator. The original generator didn't produce a high enough voltage. At first I thought it was because the coil had moved relative to the driven shaft. It had moved, but this wasn't the cause of the poor...

Mine was originally glued. When I pulled it up there was rust underneath. So I cleaned it up and treated it and just laid the underlay back down. Carpet is held by the factory plastic pins. Each year I lift the carpets and underlay and retreat the floors. Never needed to glue them down in 20 years, ...

I thought I had a scoop, but I hadn't been paying attention.

They are still pastiches.

Mine is here:-


The Hazard light was fitted after a motorway that I use regularly was down-graded to dumb status - no hard shoulder.

Goodwood’s 75th anniversary continues, this weekend with the 30th Festival of Speed - which is the event which sparked the renaissance of motorsport at Goodwood. Yesterday was the first open day, with cars being set up for practice runs up the hill, and all of the exhibitors getting ready for a busy...

That looks like a Bosch rotor arm as fitted to a 123 dizzie. If it is, note that the life of the 123 dizzie cap and rotor arm is quite short. 30,000 Kms or 18,000 miles. The central electrode in the dizzie cap wears out, and misfiring starts. Replace them both. Check the part numbers on the 123 info...

"Chris, what other spares do you tend to carry?" https://i.postimg.cc/6556ZCJy/20230711093516.jpg This useful little storage box was cobbled up from 6mm MDF and covered with vinyl etc from Woolies. https://i.postimg.cc/g21G15wZ/20230711093550.jpg Inside are a tool box, disposable gloves and paper to...

I can't honestly say where the bad belt came from. I can say that if it had been from Barratts Julian would have been on the case immediately. I've used all the usuals, Barratts, Manners, Robeys, SCParts. I've have good parts and bad parts from each and every one. Sometimes, eg oil pressure senders,...