Gearbox removal with engine in situ

Talk about the E-Type Series 3
User avatar

Topic author
lowact
Posts: 64
Joined: Mon Oct 09, 2017 10:05 am
Location: Canberra, Australia
Contact:
Australia

#1 Gearbox removal with engine in situ

Post by lowact » Wed Feb 28, 2018 2:35 am

There has been some posts related to this, I note Simon has sort of done it, with Getrag gearbox.
This article by Dick Maury: http://www.georgiajag.com/Documents/V12 ... moval.html
suggests what seems to be fairly straight forward procedure, has anyone else done it like this, might there be warnings, updates to this procedure?

V12 E-Type Transmission removal
by Dick Maury
The auto or manual can easily be removed from the V12 without pulling the engine. Here are the steps.. This is basically a 2 hour job with a lift and basic hand tools.
1. Inside the car, remove the shift knob and tapered base chrome finisher on the manual cars. If automatic, go to step 2.
2. There is a pipe that is threaded on both ends that holds the two sides of the car in place. It goes between the engine and transmission. The bolts are accessed from inside the car by lifting the carpets on the tunnel. Go under the car and attach a pair of vice grips to keep it from turning. Note the location and it will make it easier to find the bolt heads inside the car. Remove both bolts. The pipe will fall on the ground. Note that you will probably need some help putting this back in.
3. Under the bonnet, remove the bolts and nuts that hold the upper front picture frame in place. No need to drain the cooling system or remove the header tank. When done, pry the cross piece up so it is loose from the picture frame.
4. Now under the car, remove the exhaust from the olive flanges at the downpipes back. No need to take the system apart, just set aside as a unit. Drain the oil on either transmission. Remove dipstick on automatic from transmission. You can leave it hanging in place. On the automatic, there is an access point on the left side of the car to access the torque converter bolts. Remove all 4 at this point.
5. Now unbolt the front motor mounts at the base with the 5/16x24 bolts and nuts. Remove bolts and note the spacer/insulator plate for putting back when assembling
6. Place a jack under the rear of the engine or transmission and lift the rear of the transmission until it hits the tunnel. Remove the rear support plate and brackets. Note the spacers and their position for reassembly. Lower the jack to access the driveshaft bolts and nuts. Remove and press the driveshaft rearward enough to clear the transmission flange. Remove the jack and the rear of the transmission will drop some more. It will not drop out of the car.
7. If automatic, disconnect the shift lever and cable bracket from the transmisison.
8. Place a jack with soft board (2x4) under the oil cooler area and gently jack up the front of the engine. As it goes up, the rear will drop. When the rear transmission flange clears the body, stop. Install Transmission jack and remove bell housing bolts. If automatic, remove vacuum line and kickdown wiring.
9. Lower transmission out. On the manual, it might be necessary to tilt the transmission slightly to clear the torsion bars.
10. Drop the transmission. Install is reverse of the removal.
11. Note that there are no modifications to the car and no cutting, grinding or trimming.
Regards,
ColinL
'72 OTS manual V12

Link:
BBcode:
HTML:
Hide post links
Show post links


JJC
Posts: 74
Joined: Fri Apr 21, 2017 3:06 pm
United States of America

#2 Re: Gearbox removal with engine in situ

Post by JJC » Tue Mar 06, 2018 7:22 am

On a Series 3, a long wheel base of course, trick is to alter driveshaft . 1st time a pain....may have to just loosen rear (IRS) to wiggle out shaft, but future jobs a snap. Have reputable drive shaft take about 3 inches off shaft, replaced with a longer sliding yoke, re balance, and your set. Now to pull gear box, just a matter of un-do the bolts, around bell housing, etc, and pull back gear box. Maybe not 35 minutes (pulling center console takes a bit of time ), but not much longer. Changing clutch now a stress free afternoon. A lift, and another set of good hands to assist, is mandatory.

John

1973 OTS V12 since new.

Link:
BBcode:
HTML:
Hide post links
Show post links

User avatar

jagwit
Posts: 249
Joined: Thu Oct 18, 2012 6:52 am
Location: Pretoria
South Africa

#3 Re: Gearbox removal with engine in situ

Post by jagwit » Thu Mar 08, 2018 7:28 am

lowact wrote:
Wed Feb 28, 2018 2:35 am
There has been some posts related to this, I note Simon has sort of done it, with Getrag gearbox.
This article by Dick Maury: http://www.georgiajag.com/Documents/V12 ... moval.html
suggests what seems to be fairly straight forward procedure, has anyone else done it like this, might there be warnings, updates to this procedure?

V12 E-Type Transmission removal
by Dick Maury
The auto or manual can easily be removed from the V12 without pulling the engine. Here are the steps.. This is basically a 2 hour job with a lift and basic hand tools.
1. Inside the car, remove the shift knob and tapered base chrome finisher on the manual cars. If automatic, go to step 2.
2. There is a pipe that is threaded on both ends that holds the two sides of the car in place. It goes between the engine and transmission. The bolts are accessed from inside the car by lifting the carpets on the tunnel. Go under the car and attach a pair of vice grips to keep it from turning. Note the location and it will make it easier to find the bolt heads inside the car. Remove both bolts. The pipe will fall on the ground. Note that you will probably need some help putting this back in.
3. Under the bonnet, remove the bolts and nuts that hold the upper front picture frame in place. No need to drain the cooling system or remove the header tank. When done, pry the cross piece up so it is loose from the picture frame.
4. Now under the car, remove the exhaust from the olive flanges at the downpipes back. No need to take the system apart, just set aside as a unit. Drain the oil on either transmission. Remove dipstick on automatic from transmission. You can leave it hanging in place. On the automatic, there is an access point on the left side of the car to access the torque converter bolts. Remove all 4 at this point.
5. Now unbolt the front motor mounts at the base with the 5/16x24 bolts and nuts. Remove bolts and note the spacer/insulator plate for putting back when assembling
6. Place a jack under the rear of the engine or transmission and lift the rear of the transmission until it hits the tunnel. Remove the rear support plate and brackets. Note the spacers and their position for reassembly. Lower the jack to access the driveshaft bolts and nuts. Remove and press the driveshaft rearward enough to clear the transmission flange. Remove the jack and the rear of the transmission will drop some more. It will not drop out of the car.
7. If automatic, disconnect the shift lever and cable bracket from the transmisison.
8. Place a jack with soft board (2x4) under the oil cooler area and gently jack up the front of the engine. As it goes up, the rear will drop. When the rear transmission flange clears the body, stop. Install Transmission jack and remove bell housing bolts. If automatic, remove vacuum line and kickdown wiring.
9. Lower transmission out. On the manual, it might be necessary to tilt the transmission slightly to clear the torsion bars.
10. Drop the transmission. Install is reverse of the removal.
11. Note that there are no modifications to the car and no cutting, grinding or trimming.
I always thought the REAL issue was that there is not enough space for the gear lever to be moved rearwards far enough for the transmission input shaft to clear the pressure plate?
Best Regards
Philip
71 E-type V12 Coupe,
83 DD6, 80 XJS (EFI by Megasquirt & EDIS-6 + 5sp manual overdrive)
73 Jensen Interceptor
74 Interceptor (EFI by Megasquirt + overdrive 4sp auto)

Link:
BBcode:
HTML:
Hide post links
Show post links


JJC
Posts: 74
Joined: Fri Apr 21, 2017 3:06 pm
United States of America

#4 Re: Gearbox removal with engine in situ

Post by JJC » Thu Mar 08, 2018 9:51 am

Remove the gear shift lever first...two bolts......very easy.

Link:
BBcode:
HTML:
Hide post links
Show post links

User avatar

jagwit
Posts: 249
Joined: Thu Oct 18, 2012 6:52 am
Location: Pretoria
South Africa

#5 Re: Gearbox removal with engine in situ

Post by jagwit » Thu Mar 08, 2018 10:23 am

JJC wrote:
Thu Mar 08, 2018 9:51 am
Remove the gear shift lever first...two bolts......very easy.
This should be step 1 surely? There should then be no need to remove the gear knob?
Best Regards
Philip
71 E-type V12 Coupe,
83 DD6, 80 XJS (EFI by Megasquirt & EDIS-6 + 5sp manual overdrive)
73 Jensen Interceptor
74 Interceptor (EFI by Megasquirt + overdrive 4sp auto)

Link:
BBcode:
HTML:
Hide post links
Show post links


JJC
Posts: 74
Joined: Fri Apr 21, 2017 3:06 pm
United States of America

#6 Re: Gearbox removal with engine in situ

Post by JJC » Thu Mar 08, 2018 5:12 pm

Sure call it step one I guess.......I usually get the pain in the neck console out of the way before anything, but call it step one. I have pulled my gear box 3 or 4 times over the last ten years for one reason or another, and frankly, its all become rather simple. I don't think it maters if you take off the knob , but if it helps you, I would put aside an additional 5 seconds for that task. No biggie .
Happy motoring !

John

Link:
BBcode:
HTML:
Hide post links
Show post links

User avatar

driver
Posts: 40
Joined: Sat Sep 24, 2016 8:48 pm
Great Britain

#7 Re: Gearbox removal with engine in situ

Post by driver » Thu Mar 08, 2018 6:33 pm

Hi Rob Gill here,
when i took my gearbox out i removed radiator ,header tank crossrail,alternator,air box etc.moved over power steering pump so i could move engine far enough forward,so that the rear gearbox flange cleared the propshaft
flange when i withdrew the gearbox.Are you saying that it was not required to do this.? :wow: :salute:

Link:
BBcode:
HTML:
Hide post links
Show post links


JJC
Posts: 74
Joined: Fri Apr 21, 2017 3:06 pm
United States of America

#8 Re: Gearbox removal with engine in situ

Post by JJC » Thu Mar 08, 2018 7:20 pm

Not a Series 3.

Link:
BBcode:
HTML:
Hide post links
Show post links


Polse7317
Posts: 415
Joined: Tue Oct 02, 2012 12:41 pm
Location: FRANCE Aquitaine
France

#9 Re: Gearbox removal with engine in situ

Post by Polse7317 » Tue Apr 17, 2018 2:55 pm

Is it possible to remove a moss gear box and fit a getrag 265 one without removing the engine ? ( serie one FHC).... :shrug:
:fingerscrossed:

Sorry the post is not in the right place .... :roll:
Yves, happy XKE 63 fhc , w113 280sl owner
Looking for a OTS 4.2 serie 1....! :scratchheadyellow: and now have found a fhc xk 140 :lol:

Link:
BBcode:
HTML:
Hide post links
Show post links


christopher storey
Posts: 4057
Joined: Sun Mar 09, 2008 3:07 pm
Location: cheshire , england
Great Britain

#10 Re: Gearbox removal with engine in situ

Post by christopher storey » Tue Apr 17, 2018 3:27 pm

No . In any short wheelbase car, the tunnel prevents you removing the gearbox without removing the engine

Link:
BBcode:
HTML:
Hide post links
Show post links

Post Reply Previous topicNext topic