The 'E' Type Forum

Hi, Or RS Panels. I stand to be corrected here but the thing that differentiates the upright is the centres for mounting the MK IX calliper. If you are not going that way or use the cheating calliper adaptors then just the LWE steering arms on their own would do what you need. As I say I stand to be...

Hi Danial, You could measure the combustion chamber volume. Should be about 98cc +/- a couple IIRC, you would /should know that for a rebuild if trying to achieve a sensible CR across all 6 chambers. Additionally, as you have noticed the main face that the gasket would cover is generally proud of th...

Thanks for posting your experience! I agree with your conclusions re the cost of refurb the originals Vrs MX5 etc. I've been stalking thus solution for a couple of years now and more recently picked up the idea again. I've sat in a couple of MG's to get an idea, but not compared the physical size to...

What aspect made you think it was a MK2 engine?
Mike

That’s clever Colin, nice one
Regards,
Michael

Hi all, Just a brief heads up if you are in the market for the pump overhaul kit SBS7272 (applicable to all 3.4/3.8 engines except earliest XK120's, plus most 4.2 ) from SNG. Until recently I've been in the fortunate position of having a few NOS bearing assemblies to hand to over haul pumps as neede...

Thanks Colin, very useful brief. It seems that the usual Jaguar suppliers don't have and cant find a suitable seal. I'll do some more running about but time is against me right now so might have to cave and use the kit solution then continue when I have more time. Thanks for the input. Regards, Mich...

Sent you a PM Tadek!!

Apologies Tadek, I did read your post and noted the drawing and manufacturer. This is the one provided by the likes of SNG in their kits and it only suits the 1/2" shaft, as indicated by the 14.5mm dia of the smallest spring coil. My thrust was to see if any of the usuals actually have one to suit t...

OK, that makes sense, so I need a seal that will take the 5/8 dia shaft. Non of the usual's seem to do them unfortunately.
Anybody had any look finding these?

HI, I'm trying to re-seal an original S1 3.8 waterpump using a bearing assembly of the same shaft dimensions as the original, i.e. 5/8" front and back. The SBS kits sold by the usuals are 5/8 at the front and 1/2" at the rear , so you must use the new impellor supplied with the kit. The new bearings...

Hi John, I also agree with Peter, in fact so much so I'll happily accept your olds ones and recycle them for you :bigrin: At about 7-8 quid each it's an unnecessary expensive if not obviously damaged. More importantly, you will foreever worry that the next person in your position will know it's not ...

Hi Ian, Thanks for the in situ photo, makes sense now. How did you get on with hub bearings and seals if the diameter is smaller and the hub isn't listed, presumably suitable bearings etc are not listed either. A visit to a bearing specialist with the old bits in hand? Works around here if you want ...

Noted thanks, every day a learning day
Must try harder!!

Hi, Looking at the parts manual it lists C19063 from the first cars! Are you saying that there was a previous version that is not listed? If so what is your reference? Are you aware of a SB that introduces the C19063 version? Incidentally there was a pair of the C19063 on eBay at £1800 for the pair ...

Hi Steve,
I think I have sorted it now . I've never had much success with PM's, seems much too complicated for me.
Anyway, outbox shows a message now!
Cheers,
Michael

Hi Steve, I sent you a reply.
Thanks.
Michael

Great pictures BTW

8448TJ was John Cuff's car bought new by him direct from the factory in 1963. It is recorded as being transferred to the Competion Dept before delivery to have work done. John was a big friend of my Dad, Gordon Brown of Five Barred Gate Garage, John immediately started competing in it. It was progre...

Agreed they are a different part number, but very subtle differences which I think, will have to check, wouldn't preclude it. Either way the XK CR donor box has the same casing as the E-type CR box, so use that. The bell housing has a different seal arrangement as well to consider. I think I am righ...