The 'E' Type Forum

Thanks, I can now confirm that the Label with the direction arrow goes on the side of the motor at the bottom end facing the bonnet (Second Label) The First Label Smiths Code etc goes on the bottom of the heater body beside where the motor is bolted to the heater body.

The first label say?s

Smiths Code No FHB 3462/14
Serial No 243
Si Smiths Industries Ltd
Motor Accessory Division

Second label

+
-
SMITHS Made
CODE FHM IN UK
253 5751/102
VOLT 12

Hi
Looking for photo of heater showing where the two heater transfers are placed on the heater please. I belive that the one with the rotation arrow goes on the side of the motor not sure about the other one though.
Thanks

Has anyone got photos that show where the wiper motor loom connector fixing bracket is attached too? Is it attached to the wiper motor or the bulkhead?

I understand that the wiper motor colour in a series one should be dark gray hammertone, is this correct? Has any one got a colour chart that shows the correct colour?

How do you clean up the aluminium- die cast parts on the window wiper motor to look like new?

I forgot to say it is in a series one E Type 1967

Hi
Can someone please identify which is the 12 volt side of the 12v- 10v Dash transformer.
There is a marking "top" on the unit with and "arrow above one terminal, and a letter "B" and a arrow above the second terminal.
One would think that the letter "B is the 10v side is this correct.
Thanks

I have a new Lucas ignition switch (Jaguar No. C.22258) ex SNG Barratt which has four terminals, one of which is a double, making five. I need to be able to identify the terminals to the required wires on the wiring diagram, does anyone have a diagram with the terminals labelled with the correspondi...

Carburettors have been fully reconditioned on 1973 V12 with new jets (correct size) set 1.4mm (0.055?) below the bridge. Needles where fine and not replaced. I am having trouble tuning the Carburettors. The car has no emission control and the temperature sensors have been made inoperative by winding...

How far are the main jets installed on a V12 carburettor with adjustable needles? Are they pressed right home or a dimension from the bridge of the carburettor. Mine are currently pressed right home and I are having troubles adjusting the mixture as the car is running to lean at mid range, and to ri...

What was the factory height setting for the main jet from the seat?
Mine are currently around 2.3mm.

Thanks, for your replies it seems that my car may have been modified attached are details of a 1974 series 3 OTS in Netherlands with a rear anti roll bar fitted car details as follows. So do you believe that it is not necessary to have a rear sway bar?? See link http://www.xkedata.com/gallery/zoom/?...

Thanks, for your replies it seems that my car may have been modified attached are details of a 1974 series 3 OTS in Netherlands with a rear anti roll bar fitted car details as follows. So do you believe that it is not necessary to have a rear sway bar?? See link http://www.xkedata.com/gallery/zoom/?...

I am looking for a second hand rear sway bar for V12 roadster between the painter and the sand blaster it has been lost, can anyone point me in the right direction where I can get a replacement. I know that I can by upgrade ones but you have to by a pair and they are quite expensive. Any help apprec...

Can someone please explain what does the Servo motor(SM) and the temperature compensator valve(TCV) do in the air cleaners of my V12 Roadster which is a 1973 model. The Car is a right hand drive model and does not have the gulp valve or air pump etc as in the US spec cars. Are the TCV and SM only fo...

Thanks for reply Mike
Yes some photos would be appreciated.

Where can you buy replacement retracting seatbelts that use the same holes in the rear bulk head. I understand that you can get Securon 514/30 units but can they be mounted in the same upright postion with the belt coming from the top of the assembly.